 |
|
Pawtuxet industrial Park • 100 Bellows
Street, Building 13 • Warwick, RI 02888
401.941.7451 • 401.941.8345 fax |
|
|
|
Pawtuxet industrial Park • 100 Bellows
Street, Building 13 • Warwick, RI 02888
401.941.7451 • 401.941.8345 fax |
updated 4-30-06 with pics and specs
All Rigs will have been serviced at time of Auction. Batteries, both for
Cab and Deck
Engines will have been replaced with new batteries
where needed. Fluids and Filters will have been changed or topped off.
All Rigs will be ready to drive off site.
TITLES: SECURED CREDITOR HAS TITLES. COPIES ARE AVAILABLE
FOR
INSPECTION AT AUCTION SITE. ORIGINAL TITLES WILL BE DELIVERED
TO SUCCESSFUL BUYER WITHIN 48 HOURS OF CONCLUSION OF AUCTION OR PAYMENT.
Disclaimer: While Information
has been obtained from sources beleived to be reliable,
such information is not guaranteed. Bidders are encouraged to attend the inspection
or schedule an appointment. All lots sold "as is, where is" subject
to terms of sale.
fluid analysis available by request
Specifications
for Rotary & Cable Tool Drill Rigs
(Auctioneers Note: Although Information has been obtained from sources believed
to be reliable and accurate,
Auctioneer makes no warranty or guaranty expressed nor implied regarding the
accuracy of this information.
It is for this reason that all interested parties and potential bidders should
attend inspection or schedule a
appointment to inspect the rigs and lots at this auction.)
Rotary Drill Rigs:
A&W DRILL RIG #
DT-8, Lot 146
1996 Drilltech Model T25K5W, s/n 732115, mounted on 1996 Ford LNT8000 Truck,
VIN 1FDZW82ETVA31897, 300 HP Diesel Engine
Delivered with:
Sullair 900 CFM@350 PSI Drill Compressor, 5700 hrs.
CAT 3406 DITA 445 HP Deck Engine,
29,400 Lbs. Pullback, 38' Head Travel
Pipe Rack for 15- 20' sections of Drill Pipe,
Aux remote Control Station,
89 RPM 72,600 Lbs. Torque Rotary Head,
Jib Boom w/Hyd Extend 180° Swing,
7,500 Lbs. Hydraulic Winch,
Drill Table w/20' Opening & Hyd Adjustment,
48" Jaw Type Breakout Wrench,
Water Injection 20 GPM w/Foam Pump,
DTH Lubricator w/10 Gal Tank,
Control Panel & Cover w/Operators Platform,
Fine Feed and Torque Controls, Night Lights and accessories
Rear Jacks
Observed Odometer: 39,388 miles, Observed Drill Hour Meter: 5218 Hrs.
CLICK HERE FOR PICTURES OF
THIS RIG
A&W DRILL RIG # DT-9, Lot 142
1999 Drilltech Model T25K5W s/n 732406,
mounted on 1999 Sterling Truck Model 9513
VIN 2FZXEEDB6XAF21351 CAT C-12 Electronic Engine 360 HP, Rockwell RMX10-145C
10 speed
Overdrive Transmission, Jake Brake, 20,000 Lb Front Axle, 46,000 Rears
Delivered with:
Sullair 1000 CFM@350 PSI Dual Air Intake Drill Compressor, s/n 006-99001257,
CAT 3406E ATTAC 521 HP Deck Engine, s/n 6BR01191
89 RPM 72,600 Lbs. Torque Drill Head
20,500 Lbs. Feed Pressure, 30,000 Lbs Hold Back Pressure
Heavy Duty 1 3/4" Feed Chain Group
External Drill Pipe Loader for 6 Pcs. 4.5" OD X 20' Drill Pipe
Pipe Trough for 15 pcs. 2.5" OD X 20' Drill Pipe
Stabilizer Storage Trough and Hammer Holder
Remote Helpers Station w/ Independent Control for Winch, Jib Swing and Extension
Compressor Air Blowdown
20 GPM Water Injection
Blue White Foam Injection Group
Electric Air Line Lubricator for DTH Hammers w/7.5 Gallon Reservoir
172° Swing Jib Boom
(2) 48" Front Jacks, (2) 36" Rear Jacks,
48" jaw Wrench w/supports
Air Regulator for Bit Grinder
Mud Flaps. Tow Hooks and accessories
Observed Odometer: 31, 934 miles, Observed Drill Hour Meter: 6199 Hrs.
CLICK HERE FOR PICTURES OF
THIS RIG
A&W DRILL RIG #DT-10, Lot 140
2000 Drilltech Model T25K5W s/n 732472,
mounted on 2000 International Harvester Truck Model 5000
VIN 1HTTGAST7YJ004352, CAT 445 HP Engine, Fuller 18 Speed RTO-18918B Transmission,
20,000 Lb Front Axle, 46,000 Lb Rear Axle, Jake Brake
Delivered with:
Sullair 1000 CFM@350 PSI Dual Air Intake Drill Compressor, s/n 006-99009781
CAT 3406E ATTAC 521 HP Deck Engine, s/n 6BR01584
89 RPM 72,600 Lbs. Torque Drill Head
20,500 Lbs. Feed Pressure, 30,000 Lbs Hold Back Pressure
Heavy Duty 1 3/4" Feed Chain Group
External Drill Pipe Loader for 6 Pcs. 4.5" OD X 20' Drill Pipe
Pipe Trough for 15 pcs. 2.5" OD X 20' Drill Pipe
Stabilizer Storage Trough and Hammer Holder
Remote Helpers Station w/ Independent Control for Winch, Jib Swing and Extension
Compressor Air Blowdown
20 GPM Water Injection
Blue White Foam Injection Group
Electric Air Line Lubricator for DTH Hammers w/7.5 Gallon Reservoir
172° Swing Jib Boom
(2) 48" Front Jacks, (2) 36" Rear Jacks,
48" jaw Wrench w/supports
Air Regulator for Bit Grinder
Mud Flaps, Tow Hooks and accessories
Observed Odometer: 22,395 Miles, Observed Drill Hour Meter: 7789 Hrs.
CLICK HERE FOR PICTURES OF
THIS RIG
A&W DRILL RIG # DT-11, Lot 179
1992 Drilltech Model TM40 s/n 731807
mounted on 1992 Ford LNT8000 Truck
VIN 1FDZW832A3NVA29329, 270 HP Diesel Engine, 10 Speed Transmission,
18,000 Lb Front Axle, 46,000 Lb Rear Axle
Delivered with:
Sullair 1000 CFM@350 PSI Drill Compressor
CAT 3408 DITA 490 HP Deck Engine
89 RPM 72,000 Lb Torque Head
28' Mast Stroke 50,000 lbs. Holdback Pressure
(2) Drill Pipe Loaders (inside/outside) 6 pcs ea 4.5" OD X 25' Pipe
Remote Helpers Station
Airline Blowdown/Relief System
20 GPM Water Injection
Blue White Foam Injection Group
Airline Lubricator
172° Swing Jib Boom
(2) 48" Front Jacks, (2) 36" Rear Jacks
7,500 Lbs Hydraulic Winch
Drilling Accessories
Observed Odometer: 47,727 Miles, Observed Drill Hour Meter: 3972 Hrs.
CLICK HERE FOR PICTURES OF
THIS RIG
A&W DRILL RIG #DT-12, Lot 144
1992 Drilltech Model T25K3W s/n 731832,
mounted on 1993 Ford LNT9000
VIN 1FDZQ90T3PVA03584, 300 HP Diesel Engine, 10 Speed Transmission,
18,000 Lb Front Axle, 46,000 Lb Rear Axle
Delivered with:
Sullair 840 CFM @ 350 PSI Drill Compressor
CAT 3406B DITA 430 HP Diesel Deck Engine
28' Stroke, 30,000 Lbs Pull Back
Pipe Rack for 15 - 20' Drill Pipe
89 RPM 62,000 Lb. Torque Rotary Head
Jib Boom w/ Hydraulic Extend & 180° Hydraulic Swing
7500 Lb. Hydraulic Winch
Drill Table w/20" Opening & Hydraulic Adjustment
48" Jaw Type Hydraulic Breakout
Remote Control Station
1 3/4" Heavy Duty Chain Group
20 GPM Water Injection w/Foam Pump
Airline Lubricator
Operators Platform
Fine Feed and Torque Controls
Drilling & Truck Accessories
Observed Odometer: 36,068 Miles, Observed Drill Hour Meter: 3548 Hrs.
CLICK HERE FOR PICTURES OF
THIS RIG
A&W Drill Rig # DT-13, Lot 126
2002 Drilltech Model T25K5W s/n 732619,
mounted on 2003 International Harvester
Truck Model 5600i6X4, VIN 1HTXHAST43J055816, CAT C-15 455 HP 50ST Engine,
Fuller RTLO-169 18B 18 Speed Transmission w/DBL Overdrive, 4.56 Gear Ratio,
Dual Air Brakes, 100 Gallon Fuel Tank
Delivered with:
Sullair 1000 CFM@350 PSI Dual Air Intake Drill Compressor s/n 006-02003315
CAT 3406E Tier II 521 HP Deck Engine, s/n BE01223
89 RPM High Torque Head 72,600 Lbs. Pullback
20,500 Lbs. Down Feed, 30,000 Lbs. Holdback
1 3/4" heavy Duty Chain Group
External Pipe Loader for 6 Pcs. 4.5" OD X 20' Drill Pipe
Pipe Trough for 15 pcs. 4.5" OD x 20' Drill Pipe
Stabilizer Storage Trough & Hammer Holder
Remote Helpers Station for Independent Control of Winch, Jib Swing & Extension
Compressor Airline Blowdown
20 GPM Water Injection System
Blue White Foam Group
172° Swing Jib Boom
(2) 48" Front Jacks, (2) 36" Rear Jacks
Night Lighting, Security Control Covers
Air Regulator for Bit Grinder
Remote Fluid Drains
48" Jaw Wrench & Supports
Observed Odometer: 12,738 Miles, Observed Drill Hour Meter: 5147 Hrs.
CLICK HERE FOR PICTURES OF
THIS RIG
A&W Drill Rig # DT-15, Lot 128
2000 Drilltech T25K5W s/n 732460, mounted
on 2000 Sterling Model 9513,
VIN 2FZXEEDB8YAG61175, CAT 355 HP C-12 Electronic Engine,
8 Speed Fuller Transmission, 20,000 Lb Front Axle, 46,000 Rear Axle
Delivered with:
Sullair 1000 CFM@350 PSI Dula Air Intake Drill Compressor
CAT 3406E ATTAC 521 HP Diesel Deck Engine
28' Head Travel w/30,000 Lbs. Pullback
Pipe Rack for 15 Pcs 20' Drill Pipe
Auxiliary Remote Control Station
89 RPM 72,600 Lbs Torque Rotary Head
180° Swing Hydraulic Extend Jib Boom
8,000 Lb. Hydraulic Winch
Drill Table w/20" Opening and Hydraulic Adjustment
48" Jaw Type Breakout Wrench
20 GPM Water Injection System w/Foam Pump
DTH Lubricator w/10 Gallon Tank
Fine Feed and Torque Controls
Night Lights, Control Panel Cover
Drilling & Truck Accessories
Observed Odometer: 48,413 Miles, Observed Drill Hour Meter: 3729 Hrs.
CLICK HERE FOR PICTURES OF
THIS RIG
A&W Drill Rig # IR-1, Lot 130
1999 Ingersoll Rand T4W900 Drill Rig
s/n 605040, mounted on 1999 Crane Carrier Chassis Model IR2064
VIN: 1CYDCB484XT044093, CAT Model 3306C 300 HP Diesel Engine s/n 9LT22952
Delivered with:
Cummins 525 HP Deck Engine
Sullair 900 CFM@350 PSI Drill Compressor
28' Head Travel w/50,000 Lbs. Pullback
(2) Drill Pipe Loaders for 6 pcs each 25' Drill Pipe w/Outside Loader w/Hydraulic
Indexing
Auxiliary Remote Control Station
90 RPM 71,800 Lbs. Torque Rotary Head
60" Jaw Type Breakout Wrench
18 GPM Water Injection System
DTH Lubricator w/Tank
Drilling & Truck Accessories
Observed Odometer: 7146 Miles, Observed Drill Hour Meter: 4577 Hrs.
CLICK HERE FOR PICTURES OF THIS RIG
Cable Tool Rigs:
CABLE TOOL RIG #1, 60L S/N
106860, Lot 116
Sitting on a 1976
International Model 2070A
VIN D1327FBG16558, Engine: 2110A 230 HP
Fuller Roadranger 8 Speed Transmission, Jake Brake
New/Rebuilt GM Diesel Deck Engine
click here for picutres
of this Rig
Cable Tool Rig #2, A&W
Rig # BE-1, Model 22W Series Two S/N 129442, Lot #143
Sitting on 1987 International Truck
Model 1954
Continental Deck Engine, Power Take Off
CLICK HERE FOR PICTURES
OF THIS RIG
Cable Tool Rig #3, A&W
Rig #BE-2, Model 22W Series Two S/N127210, Lot # 145
Sitting on 1984 International Truck
Model 1954
Continental Deck Engine, Power Take Off
CLICK HERE FOR PICTURES
OF THIS RIG
Auction Lot Listing
Internet Bidding Registration
Leasing,
Lease to Own and Purchase Money Financing Information
& Qualifications From Excell Financial
Please pre-qualifiy prior to the auction
